Hot line：400 094 3688
发布时间：2018-07-30 11:30
Product name: pure gold leaf
Specifications :4.33*4.33cm, 9.33*9.33cm 8*8cm
Packing :500 sheets per pack
Industrial processes
Pure gold leaf with the operation process of glue
Name: gold leaf paste
Packing :12 tubes/box
Specification: tube MOQ:1 tube
Property: oily
1. The bottom material is treated, do good ash first, do primer, the bottom does not have pinhole, should level off and smooth, it's better do bright light varnish and gold paint before sticking pure gold foil
2. Mixing ratio of toothpaste glue, glue for 1 to 3 hours, mix with gasoline, the ratio of glue and gasoline is 1:2. After being adjusted evenly, spray it or apply it
3. Please pay attention to the thickness of the glue before pasting the foil. When pasting the foil, you should wear gloves and keep the environment free of dust
4. Spray 24K gold foil oil for the first time after 3 hours, and it must be thin. After the first drying, polish the surface with the finest cotton yarn and then make 24K gold foil oil for the second time.After that, you can do more protection oil according to your company's requirements.
First, the small copper Buddha statue gold process:
1. Before the gold is attached, the surface of the Buddha image needs to be treated to ensure that it is dry, dust-free, free of oil and oil wax. If there are small holes in the surface of the Buddha statue, or uneven grooves, it should be covered with a primer.
2. After the paint is dried, use a fine sandpaper to gently polish the surface to a smooth surface. At the same time, repeatedly apply a high-strength adhesive and a penetrating primer to the surface of the Buddha image to ensure a long period of time. There will be no copper rust or other rust.
3. Apply the special glue evenly on the Buddha image, then attach the raw rice paper to the surface coated with glue, make the rice paper fully contact and absorb the glue, then use the tweezers to remove the rice paper and replace it with a new one. This is repeated 3 to 4 times until the glue has only a very thin layer left, and the gold can be officially started.
4. Gently pry the gold foil with tweezers and stick it on the surface of the Buddha image. Gently blow it with your mouth to make it flat.
5, when pasting, there are generally two people division of labor, one person posted, one person at the same time with a soft cotton cloth wrapped cotton gently tapped the already attached gold foil, so that it is fully compliant. After all the gold and gold supplements have to go through the process of 2 to 3 layers, it can ensure that the surface of the gold-plated surface is full and straight, without bottoming, and there is no flying gold on the surface.
6. Finally, after all the drying, spray three layers of special high-strength protective film, and paste the gold and you're done.
Second, the large copper Buddha statue gold process:
1. The golden Buddha statue is generally a large clay sculpture. In order to set off the gold, you need to have a yellow background on the surface of the Buddha image, and then a layer of tung oil on the surface. After drying a little, you can stick the gold foil.
2, the heat when drying is very important, to be appropriate. Too dry the gold foil can not be attached, too sticky gold foil deformation stickers are not smooth. This can be said to be a work done by experience worker.
3. After gently attaching the gold foil to the surface of the Buddha image, compact it with a brush and let the gold foil completely lie on the product that is not completely dry. When the surface of the Buddha image is completely covered, it is basically completed.
The bronze Buddha statue is definitely a craft that tests the skill. If the nail is slightly forced, the gold foil on the surface of the Buddha image can be scraped off, so it is definitely a “tofu residue project”. Really exquisite skill of stick gold leaf, even if put forth your's strength, you can't scrape it.
